DeckDraftDIY plans

Deck stair calculator: how many steps for your deck height

Divide the drop to the ground by the riser height, then round up. That is the number of steps. Treads are one fewer.

For a deck 48 in high and a riser height of 7.5 in, that is 7 steps and 6 treads.

Try it free

Enter your deck height

Type the drop in inches and the stair width in feet. The calculator uses the same counting as the designer.

Change the riser height, the tread depth or the stringer spacing to see how the counts move.

1 to 240 inches
2 to 20 feet
5 to 9 inches
8 to 14 inches
8 to 24 inches

Your count

Risers
7each 6.86 in high
Treads
6each 10 in deep
Total run
5 ftout from the deck
Stringers
5each cut 7.4 ft long
Tread boards
122 boards per tread, counted at 5.5 in wide
Riser boards
7one per riser
Handrails
Drawnboth sides, in the designer

Counted for one straight stair that ends on the ground, with the designer’s starting boards (composite): risers, treads, stringers, tread boards and riser boards. The riser height, the tread depth and the stringer spacing are settings on the plan page, which opens when you unlock the plan.

Counts for three deck heights

These are worked by the tool for stairs 4 ft wide. It starts with a 7.5 in riser height, a 10 in tread depth and stringers 12 in apart. They are settings to change, not rules.

Stairs counted by the tool for three deck heights
StairsStepsTreadsRiseStringers
30 in high, 4 ft wide437.5 in5
48 in high, 4 ft wide766.86 in5
72 in high, 4 ft wide1097.2 in5

Steps are risers. Rise is the height of one step. The calculator above also shows the total run and the stair rail.

How the tool counts

  • Riser height: this sets how many steps a staircase has. The drop is divided by it, and the answer is rounded up.
  • Tread depth: how deep each step is.
  • Stringer spacing: the stringers across the stair width. The width is divided by the spacing and rounded up, then one more is added.
  • Stair rail: counted from the number of steps, along both sides.

You can change these settings in the calculator on this page, and the counts update. On your own plan they are settings on the plan page, which opens when you unlock the plan.

The tool does not answer footings. How stairs must be built is set where you live, so ask the person who builds them.

Three decks with stairs

The designer draws the stairs on the plan, with their width. Below: a raised deck, a two-level deck and wide stairs.

Plan view from the designer: a raised deck against the house wall with stairs on its front side, marked with the stair width
A raised deck with stairs on the front
Plan view from the designer: a two-level deck with stairs from the upper deck that land on the lower deck, labeled to the lower deck
Stairs from the upper deck land on the lower deck
Plan view from the designer: a raised deck with wide stairs across half of its front side, with the width shown on the stairs
Wide stairs on the front of a deck

Stairs on a raised deck

Raise the deck on the Height and stairs step and add stairs to a side. The designer counts the steps from the height you set, down to the ground.

Stairs that land on the lower deck

On a two-level deck, stairs from the upper deck land on the lower deck, not on the ground. The tool counts only the drop between the two decks.

Here the upper deck is 36 in high and the lower deck is 12 in high. The drop is 24 in, so the stairs have 4 steps and 3 treads.

Wide stairs

Stair width is yours to set. The same 72 in drop with stairs 8 ft wide needs 9 stringers, against 5 for stairs 4 ft wide. The steps and treads stay the same.

The same drop with narrow and wide stairs
StairsStepsTreadsRiseStringers
72 in high, 4 ft wide1097.2 in5
72 in high, 8 ft wide1097.2 in9

Set it on your own deck

The Height and stairs step is step 3 of 5 in the designer. Set the deck height, add stairs to a side, and drag them along it.

The link below opens the deck designer. If a deck is already drawn and saved on this device, it opens on the Height and stairs step. With no drawing saved yet, it opens on the first step.

Open the deck designer →

Free first

Designing is free, with no account.

Before you pay, you see a free preview: the item names and the first three quantities. The rest shows “Locked”. One payment unlocks the materials list, the cut list and the drawings.

Before you build

Your local building office decides what you need. Check with it before you build.

Questions

How many steps do I need for my deck height?

Divide the drop by the riser height and round up. With the tool’s starting riser height of 7.5 in, a 48 in drop gives 7 steps. You can change the riser height.

How many treads are there?

One fewer than the steps. The deck surface is the top step, so the last step up is the deck itself.

How many stringers does it count?

It divides the stair width by the stringer spacing, rounds up, and adds one. At 12 in apart, stairs 4 ft wide get 5.

Does it count stairs to a lower deck?

Yes. When stairs land on a lower deck, the tool counts the drop between the two decks, not the drop to the ground.

Does it tell me about footings?

No. This tool counts steps, treads, stringers and stair rail. How stairs must be supported is set where you live, so ask the person who builds them.

Do you build decks or fences?

Put the designers on your website. Each lead arrives with the plan drawing, the measurements and the design, and you do the quoting.

See how it works for builders →

These plans are a design aid, not engineered drawings. Check requirements with your local building department before you build.