DeckDraftDIY plans

Deck stairs ideas you can try in the designer

The designer gives you three choices for getting on and off a deck: stairs, wraparound steps along a side, or no stairs at all.

With stairs, you pick the side, set the width and slide them along the side. You can add a landing off a side. On a two-level deck, the stairs land on the lower deck.

Try it free

What the designer offers

Stairs live on the Height & stairs step, which is step three of five. You can also tap a side of the deck. Here is each choice.

  • Stairs. A new flight starts centered on its side. It is 4 ft wide, or as wide as the side in whole feet if the side is shorter.
  • Width. Make the stairs narrower or wider one foot at a time, up to the length of the side.
  • Placement. Drag the stairs along the side, tap the button that centers them, or move them to another side that has room.
  • Wraparound steps. Pick Steps along on one side or several. The steps run along the whole side.
  • Railing on the stairs. Choose yes or no for each flight.
  • Landing. Pick a landing off a side. It is a small deck section that comes with its own stairs or steps.
  • No stairs. Choose this when you want none, and the list counts none.

The designer has no stair type called wide or corner. You set a width, and you put the stairs on a side.

Where it sits in the designer

These are two screens of the Height & stairs step on a phone. The first asks how you get from the back door to the yard. The second is a flight of stairs on the front side, with its own choices below.

Phone screen of the designer at Step 3 of 5, Height & stairs, with a 16 by 12 foot deck and the question about how you get from the back door to the yard
Step 3 of 5, Height & stairs
Phone screen of the designer with a 4 foot wide flight of stairs on the front side of a 16 by 12 foot deck and the question about railing on the stairs
One flight of stairs, with its choices

Decks with stairs, from the gallery

These are 3D pictures of ready-made designs. See more in the gallery.

See more decks with stairs →

Stairs that land on a lower deck

On a two-level deck, the stairs land on the lower deck when it sits in front of them. They do not run on to the ground. The list counts the shorter drop.

The second-story page has a table that counts the same deck both ways.

See more two-level decks →More on tall and two-level decks →

How many risers and treads

The tool works out the risers from the height of the drop. These counts are for stairs 4 ft wide that go down to the ground. The treads are one fewer than the risers. Each tread takes 2 boards at the start depth.

Stairs 4 ft wide: what the tool counts
Deck heightRisersTreadsStringers
24 in434
36 in544
48 in764
60 in874
72 in1094

Riser boards are counted with the fascia, and treads with the deck boards.

Settings you can change

The counts above use these settings. They are yours to change, and the counts change with them.

  • Riser height starts at 7.5 in. The tool divides the drop by it and rounds up to get the risers.
  • Each tread starts 10 in deep.
  • Stringers start 16 in apart. That sets how many stringers a flight gets.
  • If you make no choice, stairs with 4 risers or more get a railing.

Free first

Designing is free, with no account.

Before you pay, you see a free preview: the item names and the first three quantities. The rest shows “Locked”. One payment unlocks the materials list, the cut list and the drawings.

Before you build

Your local building office decides what you need. Check with it before you build.

Questions

Can I put stairs on any side of my deck?

Stairs go on an outside side that has room. If a side is too short, the designer tells you so. A side with wraparound steps cannot also get stairs.

What are wraparound steps?

They are steps that run along a whole side of the deck. You pick them with Steps along, on one side or on several.

Can I move the stairs after I add them?

Yes. Drag them along the side, tap the button that centers them, or move them to another side. You can also make them narrower or wider.

Does the tool draw a railing on the stairs?

You choose yes or no for each flight. If you do not choose, the tool uses a setting that you can change. It decides by the number of risers.

Are the stairs in the materials list?

Yes. The list counts the stringers and their hangers. Treads are counted with the deck boards and risers with the fascia. The full list unlocks when you pay once.

Do you build decks or fences?

Put the designers on your website. Each lead arrives with the plan drawing, the measurements and the design, and you do the quoting.

See how it works for builders →

These plans are a design aid, not engineered drawings. Check requirements with your local building department before you build.